Mazda RX7 FD3S Clutch & Transmission

As a registered Mazda Parts dealer distributor, for any part you may need for your Mazda model, kindly send an e-mail to sales@racingbeateurope.com along with your vehicle model and chassis number so we can assist you.

All Mazda RX7FD3S Models come off the Mazda Production line fitted with these Exedy Clutch Kits.

  This clutch kit comes complete with the clutch release bearing, pressure plate and centre plate

Xtreme Stage 1 Australian Made Clutch Assembly uses an upgraded pressure plate with 20-40% increased clamping pressure, combined with an organic friction disc. Stage 1 delivers substantial increases in performance and power holding capability whilst retaining near factory type driveability, and is designed primarily for high performance road going vehicles.

If you want a better clutch than standard and have only minor mods to your FD  then this is the clutch for your RX-7 FD and best of all the car will still drive the same as when fitted with the standard Mazda Clutch.

Special Discounted Price 

EXEDY Stage One Sports clutches. All of Exedy clutch discs have high capacity spring center dampers to reduce the drive train shock and impact

The Exedy ZF01 Lightweight Flywheel is precision made in Japan weighing 6 Kilo will help make faster gear changes and assist acceleration.

  To fit RX7 FD, RX7 TII and 6 Speed RX8 Models

These RX7FD Xtreme Clutch kits are available with cushioned ceramic friction discs and are designed for motorsport applications where higher heat and torque capacity is required. These can also be used in some road applications.

Will handle a Torque Figure of 540 lbs which will be OK all Twin Turbo RX-7FD's and most Single Turbo cars.

Xtreme Performance - Cushioned Ceramic kit

Torque capability 540 ft lbs (730Nm)

Pressure plate clamp load 975Kg 40% Increased over standard

Cushioned Ceramic Friction Disc

To fit all models and years of RX7FD and RX7FC TII models  

This flywheel is machined with less material to assist in quicker revving capabilities. Well-suited for all single plate clutch applications. These flywheels will  work with ALL performance and stock clutch assemblies.  

If the standard flywheel is removed to fit either a lightened flywheel or a race type clutch / flywheel assembly you will need to fit this counter balance weightPlease note we will not sell after-market weights due to the potential Damage to your engine, these are Genuine Mazda items

As used in our own 700 BHP 3 Rotor Championship Winning Race Car. Kaaz Diff's are the Pro's Choice For Competition Differentials. Designed & Manufactured In Japan. These are direct replacement units and will greatly assist traction and corner exit speed for your RX7FD3S on the track or on the road ,

From street to road racing, the Racing Beat Aluminum Flywheel is ideally suited for a wide range of performance applications

With a  Torque capability of 730 ft lbs the Xtreme Clutch will handle just about any Big Turbo RX7FD, these Australian Made Cushioned ceramic clutch kits use an upgraded pressure plate combined with a ceramic friction disc in cushioned configurations.

Please contact sales@racingbeateurope.com for availability  

Racing Beat Europe" developed Exedy Stage Two Clutch with cerametalic centre plate.This clutch offers your car a very good bolt straight in upgrade.

Replacement RX7 FD Exedy Stage 2 Clutch plate.

The 6-Puck 240mm Sport/Race Clutch Disc is designed for road race and occasional drag race use.

You will need to replace either or both of these items if you are experiencing either loss of fluid, having trouble engaging gears

Clutch Release Bearing

If you are fitting a new Clutch assembly you may want to consider renewing the Clutch release arm.

4.3 RS CROWNWHEEL & PINION SET.

If the standard flywheel is removed to fit either a lightened flywheel or a race type clutch / flywheel assembly you will need to fit this counter balance weight

The Automatic Transmission  Counter Balance Weight Puller Tool will remove any automatic transmission balance weight from its taper press fit on the eccentric shaft once the flywheel nut is loosened. This is the same balance weight used with all our lightweight flywheels. 

Heavy duty High performance LUCAS OIL Fully Synthetic Gear Oil As used in our own Championship wining 510 bhp RX-8 we used this with a standard gear box for three years, so we know its great for your road cars gearbox and axle    

The Race 6-Puck Clutch Disc for the 1987-95 RX-7 TURBOII and RX-8 (240mm OD) is designed for drag and road race use. The disc incorporates six (6) sintered copper pucks and a solid hub for quick, positive engagement, greater fatigue resistance and improved heat dissipation. 

The ultimate Xtreme Twin Plate for your RX-7 TII, RX-8, RX-7FD3S This is a push type Clutch assembly that will hold 900 (ftlbs) / 1220 Nm of Torque,  so this would take 4 Rotor Turbo Power! 

It can also be in an RX-7 FD3S by using the 5 speed RX-8 Bellhousing assembly to convert from the Pull type clutch.