RX8 Rotary Engine - Internal Engine Parts

This kit is for engines that are taken apart and it is found that the only discernible wear has happened to the Rotor Apex seals that normally are found to have worn to around half the depth they should be, accounting for low compression. High Performance Goopy Apex seals are now recommended over the fragile Mazda Apex seals .

As a registered Mazda Parts dealer distributor, for any part you may need for your Mazda model, kindly send an e-mail to sales@racingbeateurope.com along with your vehicle model and chassis number so we can assist you.

As suggested this is a more comprehensive rebuild kit than the previous kit for high mileage engines or engines with issues other than just loss of compression using all Genuine Mazda parts for all (This kit saves over £250 than buying from Mazda) .

The High Performance Goopy Apex seals are highly recommended over the fragile Mazda Apex seals and have proved to be much more durable .

Additional Stationary Gear bearings and Rotor bearings available to add to order. Please make your selection below

Goopy Apex Seals  are a direct replacement for the weak less durable Mazda Apex seal are now available and with hundreds of sets of Goopy Apex seals sold over the last fifteen  years there has never ever been an issue for any of our customers.

With hundreds of seals sold Goopy seals  offer a proven more durable than stock direct replacement Apex seal for the RX-8 at a price less than you would pay for a stock Apex seal from a Mazda dealer.

99% of our rebuild kits we supply go out with Goopy Apex seals that are perfect for standard to highly modified Rotary Engines.

Also like many engine builders and tuners use these in our own Championship winning 700bhp race car .

Genuine Mazda Water Seal Kit , includes all the seals to bolt the Rotary Engine block together.

Genuine Mazda Apex seal set

When buying the low compression kit you may wish to add these Genuine Mazda Stationary Gear Bearings to the kit.  Part Number    NF01-10-E04     These bearings can be used in any model of RX-8 Engine 

Genuine Mazda RX8 Rotor Bearing x1

Rotor Housing to fit all RX8 +R3 RX-8 models .

Genuine Apex Seal Spring set

Genuine Mazda RX-8 & R3 Side Seal set (12 in a set)

Genuine Mazda RX-8 & R3 Side Seal Spring set (12 in a set)

Genuine Mazda Corner Seal set (12)

Genuine Mazda Corner Seal plug set (12)These can be used if the outer steel part of the plug is intact

Genuine Mazda Corner Seal Spring set (12)

Rotor Oil control ring set

Stationary gear O ring

Genuine Front Cover oil seal

Genuine Mazda Rear main oil seal

Racing Beat Uprated Oil Pressure Regulator - 90-95 PSI plus Thermal Bypass Pellet Replacement kit so you know the oil is properly getting to the places it should all around the engine.

RX8 Eccentric Shaft Genuine Mazda Will fit 192-231-R3 and Auto Models

The Racing Beat S-Port Templates allow you to undertake your own porting efforts on all model years of the Renesis 13B engine. 

Racing Beat developed these to put power into the mid-range where the RX-8 lacks power, this in turn translates into the car going faster up the road.  

All the gaskets needed to fit the ancillary's onto your new 192 or Auto engine

Please note this is a Special order and at times takes two weeks to assemble depending on parts avaliabilaty.

RX8 Engine installation kit. All exterior gaskets Genuine Mazda for RX8 231 6 speed engine  All the gaskets needed to fit the ancillary's onto your new or rebuilt 231 engine

Rotary  Engine Rebuild Manual This RX-8 Engine Rebuild Manual will also give assistance rebuilding ANY Rotary.

This is a 50 page paper version that's not available in Europe and will prove invaluable for disassembling and reassembling all Rotary  engines

Genuine Mazda RX8 Front Cover Gasket